1、Design and Fabrication of 150 MHz SAWF on Li_2B_4O_7 Crystal Substrate
以Li_2B_4O_7為基片150MHzSAWF的設計與研制

2、Forging Fabrication of Tubular Tuyere End Socket
貫流式風口端頭的鍛造

3、The Sputtering Process for the Fabrication of CrSi Thin Film Resistor
濺射法制作CrSi薄膜電阻工藝技術

4、Design and fabrication of auricular prostheses based on rapid prototype technology.
基于快速成型技術的人耳贗復體的設計與制造。

5、A model to describe the fabrication is set up and discussed
建立了描述此方法的模型，并進行了討論分析。

6、Fabrication study on the assembly technology of triode CNT-FED device
三極CNT-FED的封裝技術制作研究

7、The fabrication of the triode CNT-FED with newcathode-pasting technology
新型陰極粘貼技術制備三極CNT-FED的研究

8、As a new micro fabrication technology, micro electroforming I.
微電鑄，又稱精密電鑄，是一種全新的微細加工技術。

9、fabrication of integrated construction panel
整體壁板制造

10、The fabrication of multiplex high speed photocoupler is reported.
研制了一種多路高速光電耦合器。

11、The Fabrication of Fiber Grating Used in Gain-clamped EDFA
用于EDFA增益鎖定的光纖光柵的制作

12、FABRICATION OF A PARTICLE DETECTOR WITH A TOTAL THICKNESS OF 25μg/cm~2
總厚度25微克/厘米~2的粒子探測器的制備

13、Fabrication and Properties of Al_2O_3-Ni Network Composites
Al_2O_3-Ni網狀復合材料的制備及力學性能

14、Monitoring of equipment design and fabrication work.
跟蹤及監督設備設計和制造過程。

15、Fabrication of Active Layer Used in 640×480 TFT|AMLCD
640×480 TFT-AMLCD有源層的制備

16、Fabrication of high performance sintered materials through PIM
用粉末注射成形(PIM)制造高性能燒結材料

17、Fabrication and Microstructural Evolution of the Semi-Solid Al-4Cu-Mg Alloy
半固態Al-4Cu-Mg合金的制備及微觀組織演化研究

18、It's usually the hottest component and during the fabrication it probably had a lot of stresses.
它事實上是最熱的組件，在制造過程中，它可能有很大的壓力。

19、A model to describe the fabrication is set up and discussed.
建立了描述此方法的模型，并進行了討論分析。

20、The fabrication process and application of silicon carbide mirror are presented.
綜述了碳化硅反射鏡材料常用制備方法的特點。

21、Study on the Fabrication and Performance of AgI/Ag Leak Hollow Wave Guide
AgI/Ag泄漏型空芯波導的制備及其性能研究

22、Fabrication of 3D Nextel~(TM) 720/Mullite at low temperature
PIP法制備3D Nextel~(TM) 720/Mullite復合材料

23、Fabrication Techniques and Technology for Emit Needle of LMIS
液態金屬離子源發射尖的制備工藝與技術

24、Fabrication of LP Outer Cylinder for 350MW Steam Turbine
350MW汽輪機低壓外缸的裝焊制造

25、Fabrication of Pipe External Aligning Device with Hydraulic Jack
液壓千斤頂式外對口器的制作技術

26、Effects of Fabrication Errors on the Performance of an EDG Demultiplexer
工藝誤差對EDG器件性能的影響

27、Influences of plastics fabrication methods.
塑料制造方法的影響。

28、Fabrication of BST Thick Films Using a New Sol-gel Process
新型sol-gel技術制備BST0—3型厚膜

29、FABRICATION AND PROPERTIES OF C/BAS COMPOSITES
C/BAS復合材料的制備及性能

30、Progress in fabrication of C/C composites by thermal gradient CVI process
熱梯度CVl制備C/C復合材料工藝技術研究進展

fabrication翻譯